• SEC1 / SEC2: SEC A / SEC B sensor cable connection (SEC 2 only with Loop Back or RDT-systems)
• CONTROL I/O: RS485 data-interface to optional relay modules, as well as in/outputs (external reset, general relays for pre-alarm, alarm, fault, frost-alarm)
• Power supply: 24 V DC
• COM 1: RS485 data-interface for LIST master/slave or RDT-communication in a LIST network
• Com 2: RS232  Service-interface for LISTEC GmbH only
• Com 3: RS232 data-interface for unit parameterisation (Service-interface up to 115200 kb/s)
• LAN: Ethernet network-interface with 100Mb/s for LIST RDT-communication as well as commissioning and maintenance via standard browsers
• USB-host: To retrieve maintenance files and optionally saved alarm temperature data, as well as to transfer unit configurations and perform software updates

Supported software protocols

• MODBUS (RTU) via serial interface COM2
• 3964R (Siemens) via serial interface COM2
• UGM 2005/2020 (Bosch) via serial interface COM2
• EDP (Esser data protocol) via serial interface COM2
• UGM 2040 (Bosch) via LAN interface
• MODBUS TCP via LAN interface
• IEC 60870-5-104 via LAN interface

General data

• Operating temperature: -5 °C … +70 °C, (-25 °C feasible with the exception of an illegible LC-Display)
• Dimensions: 482,6 x 43,6 x 315,5 mm (w x h x d), resembling a 19” – 1 U case, 400 mm depth to be considered with connection cables attached
• Case material: Aluminium
• Weight: 2,6 kg
• Power supply: 9,5 V … 36 V DC
• Current draw: Typ. 175 mA (Normal) / 212 mA (Alarm), at 24 V DC
• Power consumption: Max. 5 W
• Relay output: 1 Relay each for alarm, pre-alarm and frost-alarm 1 Relay for fault (= active without power)
• Switching Voltage: 48 V DC / 32 V AC max.
• Switching current: 250 mA max. (resistive load)
• Input: 1 x external reset (5 V … 36 V DC)

Ordering information

• LIST CONTROLLER SEC (Unit with one sensor cable connection)
• LIST CONTROLLER LB (Unit with two sensor cable connections for Loop-Back or RDT mode)
• RDT function for LIST CONTROLLER LB
• I/P Interface and Protocol for LIST controller (via RS232 with MODBUS (RTU), via Ethernet with MODBUS TCP, one license per system)
• FCP Interface and Protocol for LISTcontroller (via RS232 or TCP with protocol UGM (Bosch) or via RS232 with protocol EDP (ESSER), one license per system)
• LISTcontroller I/P IEC 60870-5-104 (via Ethernet with protocol IEC 60870-5-104, one license per system)

Scope of delivery

• LISTcontroller
• Pre-assembled 3 m connection cable lengths for sensor cable, Control I/O, COM1 and power supply
• List memory USB flash drive

Specifications PS2408

• Mains voltage: 230 V AC +10/-20%
• Mains frequency: 47 … 63 Hz
• Output voltage: Typ. 27,6 V DC at 20 °C
• Output current: Max. 8.4 A
• Operating temperature: -5 °C … +50 °C
• Relative humidity: Max. 95% at 40 °C (No condensation)
• Dimensions: 292,0 x 220,0 x 72,0 mm (w x h x d, power supply module only) 478,0 x 266,0 x 83,0 mm (w x h x d, mounted on 19“ front-panel, w = 19“, h = 6U)
• Weight: 2,2 kg power supply module only / 3,8 kg mounted on 19“ front-panel
• Front-panel colour: RAL 9002, grey-white
• Battery charging capacity: Up to 220 Ah, chargeable to 80% within 24 hours without load

Specifications PS2408-W

• Mains voltage: 230 V AC +10/-20%
• Mains frequency: 47 … 63 Hz
• Output voltage: Typ. 27,6 V DC at 20 °C
• Output current: Max. 8,4 A
• Operating temperature: -5 °C … +50 °C
• Relative humidity: Max. 95% at 40 °C (No condensation)
• Ingress protection: IP 30
• Dimensions: 442,0 x 462,0 x 206,0 mm (w x h x d)
• Weight: 8,4 kg (Including power supply module, but without additional components)
• Housing colour: RAL 9002, grey-white
• Battery installation: Max. two 12 V / 45 Ah within housing
• Battery charging capacity: Up to 220 Ah, chargeable to 80% within 24 hours without load

Ordering information

• PS 4202 (Power supply mounted on 19“ front-panel)
• PS 2402-W (Power supply mounted in housing)
• PS 2408 (Power supply mounted on 19“ front-panel)
• PS 2408 -W (Power supply mounted in housing)

Scope of delivery

• PS 4202 with mounting accessories and documentation
• PS 2402-W with mounting accessories and documentation
• PS 2408 with mounting accessories and documentation
• PS 2408-W with mounting accessories and documentation

Relay Module RELMOD

Features

• Relay extension for LISTcontrollers to signal alarm and fault statuses to superordinate systems
• Up to 16 relay modules are addressable per LISTcontroller
• Contact multiplication programmable
• Activation of a single relay by multiple zones programmable
• Highly durable via utilisation of maintenance-free components in a modular configuration, RoSH compliant
• Very low energy consumption
• Coding Switch for module address (1 … 16)
• Inputs to remotely activate revision-mode and to initiate alarm simulations
• Inputs for external alarm- and fault-handling signals
• Input to trigger timer-controlled deactivation of differential temperature monitoring

• Operating temperature: 0 °C … +70 °C
• Dimensions: 167x 113,3 x 66,2 mm (w x h x d), snap on to 35 mm DIN-Rail
• Case material: Aluminium with transparent acrylic glass shield above main components
• Weight: 0,61 kg
• Power supply: 10 V … 36 V DC
• Current draw: 56 mA (normal operation) / 105 mA (alarm), at 24 V DC
• Power consumption: Max. 2,5 W
• Relay outputs: 16 x toggle contacts for alarm, pre-alarm, frost-alarm and fault (loop resistors may be inserted for closed-circuit monitoring)
• Switching voltage: 48 V DC / 32 V AC max
• Switching current: 250 mA max. (resistive load)
• Optocoupler inputs: 8 x electrically isolated, 5…28 V DC signals

Ordering information

• Relay Module RELMOD

Scope of delivery

• Relay Module for DIN-Rail installation

SEC 20 Simulator CSM 200

Features

• Designed to simulate sensor cable SEC 20 in test set-ups
• Simulation of up to 200 sensors
• Two temperature sensors available on-board for manual heat-up or cool-down tests
• Additional facilities to connect up to two sensor cables SEC 20 and an external temperature sensor ESA
• Four push buttons, configurable with alternative temperature values, to simulate maximum temperature, differential temperature and differential temperature pre-alarms, as well as sensor loss.
• Test set-ups with redundant LIST systems can be realised by using two or more CSM 200
• 35 mm DIN-rail mount

Specifications

• Operating temperature: 0 °C … +40 °C
• Dimensions: 102,5 x 82,0 x 42,0 mm (w x h x d, for 35 mm DIN-rail mount)
• Weight: 0,13 kg
• Number of sensors: Up to 200 (contiguous address range)
• Sensor address range: 0 … 999
• Power supply: During operation by LISTcontroller via connection cable VK SEC during set-up by PC via USB- cable

Ordering information

• SEC 20 Simulator CSM 200

Scope of delivery

• CSM 200 (pre-programmed with LISTEC default set-up)
• USB-cable, type A-B
• LISTmemory USB flash drive, including CSM 200 driver, software and documentation

Application software

• System prerequisites: PC with Windows XP Service Pack 3 and JavaRuntimeEnviroment from Version 6.35 onwards

Sensor Cable SEC 20-Ex

Features

• ATEX marking for use in zones 2 and 22
• Complete encapsulation to protect sensors from environmental influences
• Sensor spacing selectable to comply to project demand
• Pinpoint sensor location via individual addresses
• Maintenance free cable
• Aramid fibres serve as strain relief and as reinforcement in case of fire
• Easy mounting by use of diverse fasteners
• Branching of cable routes via connection boxes
• To be used with sensor control unit LIST controller
• May be combined with LIST external sensors ESA
• Up to 3.200 m combined cable length, respectively up to 320 sensors per LIST controller

General data

• Type of protection zone 2: Ex II 3G Ex nA IIC T4 Gc
• Operating temp. zone 2: -20 °C … +80 °C, from 70 °C protected from mechanical impact energy (EN 60079-0 / 26.4.2)
• Type of protection zone 22: Ex II 3D Ex tc IIIC T125 °C Dc
• Operating temp. zone 22: -20 °C … +70 °C
• Cable diameter: Typ. 18 mm
• Flat conductor resistance: Typ. 85 Ω / km (single conductor)
• Sheath material: HM4 mixture, halogen-free and flame retardant, according to EN 50267-2-1:1999-04,EN50267-2-2:1999-04, EN 60332-1-2:2005-06, EN 60332-2-2:2005-06, EN 61034-2:2006-03, IEC 60754-1, IEC 60754-2
• Weight: Typ. 0,45 kg / m
• Sheath colour: Grey or black
• Marking: Consecutive number printed at each sensor location, followed by cable identifier
• Deliverable cable length: Up to 2.000 m, prefabricated cable sections on request
• Mounting temperature: ≥ +10 °C
• Bending radius: ≥ 30 cm
• Verified and approved to: FprEN 54-22:2012 by VdS Schadenverhutung, VdS no.: G 213072 Meets requirements of environmental classification III

• Ordered sensor cable length may be shipped as a cable ring in a carton, on a one way drum, or on loaner KTG-drum and pallet
• ATEX markings for every separate sensor cable section

Cable construction

• Four-core flexible flat cable with temperature sensors
• Filler material with strain relief
• Aluminium foil shield
• Sheath with imprints at each sensor location

Cable Imprint

• Imprint 1: The sensor marking is used in cable lists, delivery notes etc.
• Imprint 2: Static marking only